A Dutch version is also available on our web site.
Une version Néerlandaise est aussi disponible sur notre site web.
Een nederlandse versie is ook beschikbaar op onze website http://www.qbus.be/qfiles/software/QBUS%20software%20versies.txt


Program corrections to QBUS Serial Manager II


V2.6.8  (2017.09.11)
1. Save IR parameters on SWC04I
2. Support for REL04SA (s/n:06xxxx)


V2.6.7  (2015.12.08)
1. Support for ANR04SA with s/n:24xxxx


V2.6.6  (2015.10.15)
1. Support for INP02 with s/n:89xxxx


V2.6.5  (2015.09.25)
1. Support for REL08 with s/n:16xxxx


V2.6.4  (2015.09.14)
1. Support for DIM04SA and DIM02SA with new firmware(V10.0 and higher)


V2.6.3  (2014.03.31)
1. Support for DIM04SA and DIM02SA (s/n:11xxxx)


V2.6.2  (2013.10.11)
1. Support for REL04SA (s/n:05xxxx)


V2.6.1  (2013.07.04)
1. Err.3265 solved when changing name of new modules REL02 and SEN01


V2.6.0  (2013.05.28)
1. Support for REL02/ROL01 modules s/n:750000-789999
2. Support for SEN01M/SEN01T/SEN01NTC s/n:700000-708999 and 71xxxx


V2.5.38 (2012.08.29)
1."Invalid Data Length" solved when sending data to INP-modules s/n:84xxxx


v2.5.37 (2012.07.05)
1. Support for REL08 s/n:14xxxx
2. Support for INP08/INP16 s/n:84xxxx and 85xxxx


v2.5.36 (2011.11.17)
1. Destroy parameters in MDO01 if TH used, solved.


V2.5.35 (2011.10.11)
1. Err. 3021 solved when immediately opening the 'outputs' screen.


v2.5.34 (2011.09.13)
1. Destroy parameters in MDO01 if TH used, solved.


V2.5.33 (2011.08.04)
1. Print logic visible again
2. Support for DIM04/500U modules


v2.5.32 (2010.08.03)
1. Text on TSC left aligned insteaf of centered
2. Err.3021 solved when creating new TH on TSC58
3. Update parameters screen REL04-PID
4. Support for INP02 modules 86xxxx
5. Reorganise logic A>63 also possible for addresses of a control table


v2.5.31 (2009.09.21)
1. Err3265 solved when pressing 'used in'


v2.5.30 (2009.09.10)
1. Support newREL04 (201xxx) and REL08 (13xxxx)
2. IR Codes Telenet Digibox added in QBUS.SDB


v2.5.29 (2009.06.09)
1. Small bugs solved: short scene names, long name in TSC, direct TX from alarm window; Simulation shutters STOP...


v2.5.28 (2009.02.06)
1. Err.13 solved when controling dimmers from the dimmermodule (bug since V2.5.26)
2. Modified translations


v2.5.27 (2009.02.05)
1. Err.3021 solved when creating a new output on REL0x or SWI04 (bug since V2.5.26)


v2.5.26 (2009.01.29)
1. Speed up 'Search for Serial interfaces'
2. All outputs for DEMO CTL are 'not virtual'
3. Check added when programming 'long' data in modules 
4. Flags Timeoff on TH correctly shown
5. Print alarms in logical expressions


v2.5.25 (2008.12.12)
1. Set TH to a valid program after sending to new CTL or 'clear' CTL
2. Test TH program added in 'outputs' + visualise outputs after "Read values"
3. Limit set static IP to 10.x.x.x or 172.x.x.x or 192.x.x.x


v2.5.24 (2008.12.03)
1. Correction on parameters Timebase for ANA04/REL04-PID
2. Simulation "Shutter down" added
3. Check SMS tel.nrs and Verify SMS texts added


v2.5.23 (2008.11.21)
1. Correction on parameters for Speed1-2 on REL04-PID


v2.5.22 (2008.11.13)
1. Message when creating too many scenes or schedules for CTL16/32/64
2. Support for new ANA04-PID modules s/n:26xxxx (Beta-Test)


v2.5.21 (2008.10.03)
1. Support for new OUT08 modules s/n:92xxxx (Beta-Test)
2. Hide leds on INP08/16
3. Thermostat can be set as PID
4. Support for new REL04-PID modules s/n:21xxxx (Beta-Test)
5. TSC58 s/n >=831000 + activate output after 'end sleep'
6. Clear softlink when changing Source Output (bug since V2.5.18)


v2.5.20 (2008.09.25)
1. Support for new ANI04 modules s/n:88xxxx (Beta-Test)
2. Err.100 solved if many logical expressions with TEMP.x


v2.5.19 (2008.09.03)
1. Reading of set output to OFF if subaddress <> 1 in logica corrected.
2. Disable button 'Used in' if no output selected


v2.5.18 (2008.08.13)
1. IntelCardio mode


v2.5.17 (2008.08.01)
1. Trigger on LDR in new MDI's was divided by 2 every time module was selected
2. Communication check with 1 module added


v2.5.16 (2008.07.30)
1. 'Adjust temperature' can be set in MDO01


v2.5.15 (2008.07.30)
1. 'Clear CTL' before sending 'all data'


v2.5.14 (2008.07.28)
1. Support temperature switching for new MDO01 (s/n:96xxxx)
2. Set type of control table (Ethernet, IRS01, THI01, SMS01, Cardio...)
3. Set SER02/Cardio parameters (s/n:979xxx)
4. Strange behaviour of matchtexts with length=5 on SMS01 solved


v2.5.13 (2008.07.14)
1. Err 11 solved when adding IRG04 >=980250
2. Display correct name of MultiLink
3. Adjust brightness of leds on SWc0x with M or I options


v2.5.12 (2008.07.10)
1. Err 340 on Print and E-mail register form solved


v2.5.11 (2008.07.09)
1. Error solved in 'used in' in scenes.
2. Missing MSMAPI32.OCX in 'register' solved


v2.5.10 (2008.07.07)
1. Error solved: wrong logic lines set to "THEN"


v2.5.9 (2008.07.04)
1. 'Short name' for scenes added
2. Link to multilink hidden in logic
3. Close TCP/IP connection When opening a new QDB
4. Registrer form added


v2.5.8 (2008.06.26)
1. 'Search for ETH02 modules', also will find modules on different subnet.
2. Upgrade to v2.1.1 also available for 'older' ETH02 and prototypes.
3. Ignore events if connected to Stijnen 'Qbus Home Server'.


v2.5.7 (2008.06.18)
1. Support for universal generator IRG04 s/n >=980210


v2.5.6 (2008.06.04)
1. Err 104 when uploading 'empty data' solved


v2.5.5 (2008.06.02)
1. Wait IR repeats (/10ms) adjusted for THI01 (/1ms), SWC04I (/1ms) and new IRG04(/20ms)
2. Possible to save ip address and portnr in QDB
3. Upgrade ETH02 to firwmare 2.1.1 built in (New layout, support for all modes, all channels in 1 list, ...)
4. Show in 'used in' also 'temporary disabled'


v2.5.4 (2008.05.08)
1. Extra check when setting fix IP
2. Support communication with Stijnen "Qbus Home Center" v1.9 or higher
3. On-line commands improved
4. THI01 with menu control also possible for direct control (Y/N)
5. IR Sample Header can be edited


v2.5.3 (2008.04.29)
1. Comment field added in logic and switchtimes
2. Audio support in new IRG04 s/n >=980210
3. "Remote support" (Teamviewer) built in (F12)


v2.5.2 (2008.04.16)
1. Light Scale (0-63) modified on SWC0xM 
2. Copy from... control table again possible 
3. Softlinks are not cleared when sending 'All Data' if 'All logic' was not checked


v2.5.1 (2008.04.14)
1. 'File not found' solved when Upgrading ETH02 on some PC's


v2.5.0 (2008.04.10)
1. Easier making first connection. Show also firmware version of ETH0x + set fix ip ...
2. Create new alarm does not overwrite the first alarm with defaults anymore
3. Error creating new control table solved.
4. Add and delete line in control table in THI01 supported.
5. Upgrade ETH02 to firwmare 1.5.1 built in (bug 'first menu sometimes blank" solved)


----------------------------------------------------------------------------------------


v2.4.19 (2008.03.17)
1. THI01 s/n:080250 or higher with menus


V2.4.18 (2008.03.07)
1. Alarms also in new SWC02 firmware 4.6 or higher
2. Print alarma in scenes and switch times
3. Monostable outputs removed from list in scenes
4. Enable Form after RX test and Comm.error
5. Support for new MDI01 (s/n>=951000 and higher; FW:V6.01) and MDO01 (s/n:96xxxx)
6. Error 3020 solved on SWC0x if preset name was longer than 19 characters
7. Read correctly "M" or "S" from Timer1,2,3


v2.4.17 (2008.02.14)
1. Alarm settings "completely out" will also be saved now
2. "Set all values" or "Clear all values" in a scene also possible for alarms
3.  CTL V9.32: Toggle outputs in a scene or switch time: immediately on or off ("ON" or "OFF") or delayed on or off ("On" or "Off")
4. "ELSE" added in logic for Alarms
5. Outputs after the alarm address in switch times will also be executed now
6. safety in MDI01 and SWC0xM: 'First trigger' must be greater than 'keep trigger'


v2.4.16 (2008.02.05)
1. Alarm SMS text can be edited


v2.4.15 (2008.02.05)
1. Controle s/n from CTL in setup and transmit data
2. Alarm number 63 always 'Stop All Alarms'
2. Alarms added in scenes and switch times


v2.4.14 (2008.01.30)
1. Layout of SWC04/Niko changed (M/I/T)
2. Err.5 solved when transmitting to an SWC if no alarms were set


v2.4.13 (2008.01.30)
1. Alarmen (1-63; names; blinkking of leds,block inputs...) for SWC04 added
2. Max. delay between 2 IR codes=150ms
3. Search for 'used in' also in TH Sensor in SWC0xT


v2.4.12 (2008.01.11)
1. Manually creation of Philips RC5 Infrared codes added


v2.4.11 (2008.01.03)
1. SMS commands will also be accepted with up to 5 additional spaces between command and status
2. SMS commands for Timers also possible with variable (time divided by 2)
3. On-line command TH+/-/Prog. added on SWC0x


v2.4.10 (2007.12.28)
1. 'Alarms' can be sent from SMS01 (controled through logic)
2. Integrity CTL extended (<> modes)


V2.4.9 (2007.12.13)
1. Reset TimeOff off Thermostate to 30m solved.
2. Err201 when programming TSC solved. The link to a deleted TH is also removed.
3. Clear complete controler with s/n:000001 and synchronise time to the pc clock.
4. RX and TX IR samples on IR swithces (SWC04I,SWC02I,...) added.


v2.4.8 (2007.11.20)
1. "Read values" added to THI01.
2. Support for new SWC04 and SWC02... (s/n:300000..399999 and 500000..599999)
3. Support for new REL04 s/n:20xxxx and ROL02 s/n:28xxxx
4. If output was deleted, search everywhere for "in use"
5. Show also first 4 IR inputs on IR page for SWC0x


v2.4.7 (2007.10.09)
1. Support SWN04... (s/n:400000..499999 new range of Niko RGB bus switches)
2. Verify error (Err201) on DIM04 solved


v2.4.6 (2007.09.27)
1. Module not found (Err255) occured sometimes while programming SWG04 and SWC04: Timing changed.


v2.4.5 (2007.09.20)
1. Also print inputs on Page 2 for SWx04
2. "UP/Down" Down function was sometimes blocked for CTL16/32/64
 

v2.4.4 (2007.09.17)
1. Default RC 'Off' instead of 'Auto' for SWC04 and SWG04 to avoid too much RC's
2. Verify init texts in CTL
3. Restore link 'Help' to website
4. Enable alles "led on" and "led off" for TH prog on SWC04
5. Economy and Comfort serperately configurable on TimeOff of Thermostate
6. Display on 'used in logic' if it is a condition or a result
7. Overflow solved if 'new input' and more than 255 in/outputs on SWC04
8. 'New output' on SWC04 on Page 2 was assigned to Page 1
9. Support for SER02 (s/n:97xxxx)
10. Explanation for 'Searching connection' improved


v2.4.3 (2007.07.27)
1. Error no current record solved when adding logic if 'many' logics.


v2.4.2 (2007.06.19)
1. Overflow solved in 'modules' if more than 255 outputs
2. New logic, scene, switchtime, control table with "+" button
3. Keep last module if sorted on description
4. Show delay on-off on relay moduels for toggle outputs
5. Search 'used in' also in button 5-8 and IR inputs on new switches


v2.4.1b (2007.05.31 22:35)
1. Verify error solved for new modules with s/n > 091000


v2.4.1 (2007.05.31)
1. Scenes or outputs in control table could be lost. Please check your data
2. SMS01 (s/n:91xxxx) extra parameter added: Who has access, Who gets reply, Debug Y/N, Signal strength, ...


----------------------------------------------------------------------------------------


v2.3.12 (2007.05.15)
1. Runtime error 3315 solved when adding a THI01
2. Channel on THI01 immediate command Yes/No (double click on list)
3, Always count Audio address as output in CTL16/32/64


v2.3.11 (2007.05.07)
1. Clear SMS Alarm texts and init Headers
2. SWC04: Color adjustable if no input selected
3. SWG04: fixed green


v2.3.10 (2007.04.21)
1. Error 104 solved when sending data to SWC04.


v2.3.9 (2007.04.16)
1. New controler names in Setup.
2. Calculate module type from serial number.
3. Support for SWC with IR remote control (8 additional inputs)


v2.3.8 (2007.03.12)
1. Several run-time errors solved when editing modules SWC/SWG
2. SMS01 module supported.


v2.3.7 (2007.02.09)
1. List outputs simulations: 'All' displayed too many outputs.
2. On-line floor map limited to 40 outputs/map
3. Extra colors, settings, light parameters,TH,... configurable on SWC0x and SWG0x
4. Alarm address=19 instead of 20 (CTL V9.30)
5. Send extra texts (YES/NO/UP/DN) to CTL v9.26 and higher in accordance to language


v2.3.6 (2006.12.27)
1. Send audio addresses (def:A32,33,34,35) to IRG04 s/n:980101 and higher


v2.3.5 (2006.12.08)
1. Run-time error 3421 solved when selecting TH on SWC if too many outputs in use.
2. TSC from s/n:830200 and higher: extra parameters added
3. Read IR-samples from THI01 added + extra parameters


v2.3.3 (2006.10.30)
1. Add Alarm-address for SWC0x and SMS01 via Setup
2. Create audio addresses from A32 (+step 16...)
3. Support for IRG01/04 (s/n:9801xx)
4. Selection of iniversal IR codes on THI01-display
5. Run-Time Error '3021' when "Search for modules" in s/n:07xxxx,15xxxx,... solved


v2.3.2 (2006.09.29)
1. "Overflow" solved when output selected in list when more than 255 outputs.
2. Bus communication check added in tools.
3. Support for RGB switches (s/n:23xxxx).


v2.3.1 (2006.08.04)
1. Data receive time-out too short for communication with ETH. (only DLL)


v2.3.0 (2006.07.31)
1. 3 communication retries also built in via ETH0x.
2. Upload firmware ETH0x added in setup.D
---- PLEASE UPGRADE TO V1.4.1 ! ----- (except MAC00-20-4A-8D... Please contact support)
3. Audiosource can be set in switchtimes.


----------------------------------------------------------------------------------------


v2.2.11 (12/6/2006)
1. Some data of simulation was lost during sent and received. All data completely sent and received now.
2. Copy simulation (one day) added.


v2.2.10 (7/6/2006)
1. Spanisch language added.
2. Error MDI01 "overrule" if blanc outputs solved.
3. Error if floormap background pointed to an invalid drive solved.
4. Audio samples 980001-4 are correctly sent now.
5. Setup files extention 'qbus' instead of 'qdb'. Data files remain '.qdb'


v2.2.9 (31/05/2006)
1. Portugese language added
2. Edit and sent list of simulation added


v2.2.6 (20/03/2006)
1. Thermostat control also available on floormap
2. Audio modules 99xxxx are transmitted correctly
3. 'Alarm' mode added


v2.2.5 (23/02/2006)
1. Verify error MDI<=950020 solved
2. Bugs in On-line floormap solved
3. Audio volume in scene correct when pressing set or clear all
4. Samples & IR transmitter (s/n:98xxxx) added
5. THI-display with universele IR (s/n:08xxxx) added
6. Export print to "print.txt" added
7. INP16 module supported


v2.2.4 (09/01/2006)
1. 'old' links will we cleared for up-function of dimmers.


v2.2.3 (06/01/2006)
1. Error "No current record" solved when scanning for modules (bug only v2.2.2).
2. Switchtimes after switchtime with all days deactivated, were not executed. This is solved
3. When a dimmer was removed from a switch, the programming of a dimmermodule remains unchanged.
4. Extra noise/priority flags for MDI01 added.


v2.2.2 (13/12/2005)
1. Dimmermodules 09xxxx, 17xxxx,... also reprogram when fadeout had changed.
2. Support for new modules with new Qchip
3. Recognition of new modules and firmware version.
4. Link to download page in menu "Help" to download new releases and manual
5. Reset COMport when communication error occured.
6. Remote table (A1) can not be deleted and is default for IRS01.


----------------------------------------------------------------------------------------


v2.1.22 (14/11/2005)
1. All properties for MDI01 built in.


v2.1.21 (13/10/2005)
1. Import: 17 instead of 16 outputs possible in each switchtime.
2. New detector MDI01 (95xxxx) supported.
3. Cancel and verify upload/download improved.


v2.1.20 (04/08/2005)
1. Reorder addresses if A>63 in logic.
2. Swithctimes were cleared when no data needed to be transmitted.
3. List "Used in" added in outputs and scenes


v2.1.19 (06/07/2005)
1. Timing Serial communication improved.
2. Volume correction not reset anymore.


V2.1.18 (28/05/2005)
1. Error 94 solved when entering a new module.


V2.1.17 (27/05/2005)
1. In SWI04 Low and High led can be set and cleared even if no input is selected
2. Simulation can be activated using a switchtime
3. Texts for Simulation adjusted for CTL v9.18 or higher


V2.1.16 (25/05/2005)
1. 'Holes' in switchtimes are totally cleared now
2. Simulation can be controlled from a logic function (CTL v9.18 or higher)
3. Temporary disabling logic or switchtimes added
4. Reading an INP module with T2 on 3rd place is an SDI04 only when the inputselection is a 'switch'.


V2.1.15 (12/5/2005)
1. IP communication password added (ETH firmware v1.4.0 or higher needed).
2. Time values when reading simulation adjusted (BCD-DEC).
3. Adres from output 1-2 and 3-4 in DIMxx should always be the same!


V2.1.14 (6/5/2005)
1. When a module is deleted, every output is marked as fictive.
2. CTL00-01-02 in setup, with message when maximum is exceeded.
3. French texts updated.


V2.1.13 (15/4/2005)
1. Volume correction for each audio source added.
2. A(21) can also be used for modes other than "LC"
3. Up & down for dimmers, shutters and audio volume is possible on every button of a switch.
4. List of modes translated.


V2.1.12 (8/4/2005)
1. Send Sony IR codes and read 'samples' built in.
2. Setup error concerning missing OCX file in control panel solved.


V2.1.11 (6/4/2005)
1. If more than one audiomodules 99xxxx, the exact room is choosen now.
2. Change mode from Start/Stop to Toggle possible (new inputmodules 87xxxx)


v2.1.10 (5/4/2005)
1. The really used outputs for a thermostate will be calculated for CTL00 and CTL01 instead of always 4.


v2.1.9 (31/03/2005)
1. Audio selections possible in modules 99xxxx


V2.1.8 (30/03/2005)
1. Verify modules was not always correct.
2. Search for ethernet interfaces built in.
3. New TH and delete TH possible in Touchscreen window.


V2.1.7 (23/03/2005)
1. Audio sources and IR texts transmission added.
2. Last setting in control panel are saved.


V2.1.6 (21/03/2005)
1. Error solved when deleting a dimmer which is in use in a multilink.
2. Ethernet communication port programmable.


V2.1.5 (10/03/2005)
1. Read audio address bit 0-3 instead of 1-4
2. Delete shutters in online floormap built in
3. Potuguese translation (Brazilian) added.


V2.1.4 (5/3/2005)
1. Send and receive 'samples' for IR interface (9801xxx and higher) added.
2. Preset Sequence always completely transmitted.


V2.1.3 (3/2/2005)
1. Values of simulation read changed.
2. On-line control simulation (On / Off / Record) built in.
3. Memory dump corrected
4. If A21 is not used as display, the correct output remains during import.


V2.1.2 (28/1/2005)
1. Memory dump built in
2. Read Simulation built in.


V2.1.1 (20/1/2005)
1. Print outputs with mode T1-3 was always in seconds.
2. Download softlinks to scenes built in.
3. In logic TEMP.x was read als TEMP.x+2
4. Delete a group of outputs in control table showed a wrong channel number.
5. TCP/IP communication through port 8444 and 8445 instead of 4444
6. A fictive dimmer immediately gets an address (for multilinks and logic)
7. Error when importing long Start/Stop names solved.


----------------------------------------------------------------------------------------


V2.0.32 (30/12/2004)
1. Print scenes, switch times, modules, remote tables and logic built in.
2. Runtimer Error 94 solved when changing mode and no multi link is present.


V2.0.31 (19/12/2004)
1. Import data sometimes took the wrong moduletype (SDI04 instead of SWI04/INP04/INP08)


V2.0.30 (17/12/2004)
1. Verify REL04 and ROL02 modules from serial number 045000 instead of 042000
2. Changed name of switchtime immediately saved. Not when exiting the field
3. Print Outputs built in
4. Import data: All data marked to be uploaded.


V2.0.29 (9/12/2004)
1. Download audio and logic (incl. softlinks) built in.
2. Upload data: extra selection possible 
3. Download "simulation" selection improved.


V2.0.28 (25/11/2004)
1. If there was only 1 switch time, it was not sent correctly.
2. Timer5 Detector input also possible through - New output - on 3rd button of SDI04
3. Verify modules a little bit slower. Sometimes the verify was too fast. ( min. 2.5sec after programming last module)
4. After switching between sorting modules, the last selected module is selected again.
5. Each scene that was opened, was unnecessary sent to the controller.
6. Read and verify new dimmer module (09xxxx) built in..
7. Daylight saving activated by default en sent together with the other parameters.


V2.0.27 (17/11/2004)
1. When you opened the control panel and a TH was on 'economy', The text mas net set correct.
2. Multilink activated by a dimmer makes the attached dimmers 'follow' instead of only on/off. Also other toggle and timers can switch on/off
3. COM-port up to COM32: instead of up to COM16:
4. Tooltiptext for timers on the floor map corrected with factor 2,55
5. Error 3021 during copy a remote table solved


V2.0.26 (12/11/2004)
1. Accepted characters for names of outputs, scenes, ... extended to all characters ASCII 32 - 127.
2. Multillinks also possible for Toggle, Timers, ....
3. New output: not in simulation by default
4. Start/Stop: online test on modules or control panel: also OFF (=STOP) added.
5. 1-Button shutters in scenes and switch times created an 'Overflow' since V2.0.24: this is solved now


V2.0.25 (5/11/2004)
1. Display warning for up/down was not correctly saved.
2. Multilinks for up/down (also reversed function) finished.


V2.0.24 (4/11/2004)
1. Daylight saving setting also saved in database.
2. After "Clear input" on input modules (SWI, INP, SDI, ...) the input selection for the 4 inputs was set to "Normal Closed". This remains unchanged now.
3. Upload of 1 (=current) scene is also possible now.
4. Verify modules faster.
5. A switch time without any actives days blocked the next switch times. This switch time is now sent as an empty block.
6. Download outputs keeps the long output names.
7. More logic expression (+/- 60 logic lines) per address possible.


V2.0.23 (29/10/2004)
1. Error message when 'Cancel' was pressed in wizard new outputs solved.
2. Logic and Multilinks for shutters updated (with "Stop" function)
3. Control integrity built in when opening a database.


V2.0.22 (22/10/2004)
1. Multilinks add, delete and modify possible via properties for dimmers and shutters (logic / link)
2. If there was a problem at the beginning of the upload and this was ignored, the last part of the logic was not sent. This is solved now. 


V2.0.21 (19/10/2004)
1. "Timer5 detector" input also possible to choose on the 3rd place of an SDI04. "Timer5 Manuel" can be put on a different switch an has always priority.
2. TCP/IP communication can communicate through another serial address (If used together with a SER01).
3. Parameters Timer5 also changeable on the manual control.
4. Small explanation of timers in properties.
5. Changing scene names sometimes had strange behaviour.


V2.0.20 (5/10/2004)
1. Searching for  modules. Errors finding module 03xxxx, 042xxx, solved..
2. If the address (=mode) of an output changed, the remote control tables were this output is in, are also sent.
3. Editing names in menu 'Outputs' improved.
4. Download of 'selective data' updated.


V2.0.19 (24/9/2004)
1. Online floor map: Window sizeable. Mode Up/down, Timer4 en Timer5 added.
2. Copy a remote table added.
3. Icons for menus for touch screen added. 


V2.0.18 (21/9/2004)
1. Properties 'Timer4' & 'Timer5' only worked in seconds. Now also X minutes possible.
2. Setup changes to switch faster to different COM ports.


V2.0.17 (17/9/2004)
1. Test expressions in logic with outputs >A63 is not possible. If this is the case, a reorganisation of the memory is executed before sending this data.
2. Last used QDB and directory could not be longer than 50 character. Maximum length increased.
3. Saving and editing IP address or host name instead of a fix IP
4. Sort modules by place/description built in.


V2.0.16 (7/9/2004)
1. Import and storing audio in scenes and switch timers updated.
2. Screen lay-outs changed.


V2.0.15 (31/8/2004)
1. Import dimmers and up/down gave too much "duplicate names".
2. Import correct volume in scenes.


V2.0.14 (20/8/2004)
1. Errors during import scene numbers in remote table, logic from 2nd logic address instead of always 1st address, values of dimmers in scenes factor 128/100 wrong, read touch screen data, solved
2. Double names during import are shown and corrected.
3. Control panel finished: scenes, simulation, colours, ...


V2.0.13 (13/8/2004)
1. Error solved when deleting an output in switch times if you click on the arrow.
2. Online Control Panel added.
3. First TCP/IP communication TCP/IP built in.


V2.0.12 (27/7/2004)
1. Some switch times didn't work. Communication routine updated.
2. Changing names from a logic expression built in.
3. Names maximum 25 characters long.


V2.0.11 (22/7/2004)
1. Interrupting communication improved.
2. Remote table adapted for touch screen (menu's)
3. When error in communication, sometimes the maximum used address was not changed.
4. Add and delete a line in a remote table added. 


V2.0.10 (6/7/2004)
1. Changing the mode (eg from Toggle to Timer1) the output was marked as "fictive output". This problem is solved now.
2. Creating audio outputs and changing audio sources built in.
3. Online floor map starts up in SETUP mode in order to set up the screen when you have no communication.

V2.0.9 (2/7/2004)
1. Possibility to import Audio , controls on switch, in scenes, switch times and remote table.
2. Verify programmed modules.
3. Mode "Scene Sequence" added.
4. Searching for modules as from serial number xxxxxx built in.
5. Copy scenes added




Previous versions:
- Online floor map: controlling dimmers, toggle, timers and changing background map and names.
- Extra parameters thermostat: active programs, hysteresis, alarm, time-off
- On-line test switch time
- Language versions: Dutch, French, English and German
- Auto detect COM-port
- Import data from 'old' software
- Softlinks are threated as a 'simple' logic expression.
- Online TEST button on modules, outputs, scenes,....